Programmable Logic Controllers: SCADA Devices of a New Breed

Programmable Logic Controllers, PLCs, are small computers used for automating and controlling electromechanical processes. They're made with a lot of input and outputs in mind. They are built to handle vast temperatures, electrical noise, and vibration common in industrial processes.

PLC's are a type of Supervisory Control and Data Acquisition (SCADA) device. They monitor, automate, and provide a human interface for electronic control of processes. They take what would be a complicated mechanical process and provide the info and interface to make it an electronic one.

To provide this high level of process control, a PLCs gathers data through a series of discrete and analog sensors. It then either acts on the data in instances where it's been programmed to take action, or provides its user with relevant data so he or she can take action. And because they're software controlled, PLCs are adaptable and allow for fast, relatively low-cost reorder of processes.

A PLC provides data and control access to site equipment from a central SCADA console. If the central SCADA console can be described as the brain of your SCADA system, then the PLCs are the nerves and muscles. They inform the brain and act on its commands.

Before PLCs, Automated Processes Took Time to Automate

Prior to the invention of PLCs, automating the same processes required hard-wired relays, cam timers, and drum sequencers. Any change in the process required a costly delay while relays were rewired and other gear was fully calibrated. PLCs were invented as an electronic way to skirt these issues, allowing for faster software calibration of processes.

Due to high initial costs of install, PLCs are used in specific cased. For example, those processes where the requirements for automation are complex and subject to change. Also, where the output justifies the cost.

Remote Telemetry Units: An Alternative to PLCs

In recent years many smaller industries have tried to get cut the high cost of PLC install. They also tried still satisfying their desire for automation by using programmable logic relays, or PLRs. PLRs are much like PLCs, but with fewer inputs and outputs and are primarily used in light industries with fewer processes to automate.

However, while PLRs provide high-level algorithmic control for automation, they often aren't scalable. Additionally, they provide many sensors for info reporting. That's why some businesses are now opting to utilize Remote Telemetry Units, or RTUs. RTUs are small-scale, PLC-like devices. They are equipped with a large number of discrete and analog sensors. They can monitor processes and control relays to execute basic controls.

RTUs like the NetGuardian series have proven to be a low-cost solution for monitoring actions, good for network, communications, and transport processes. They provide alarms to alert techs to problems, and take action to minimize any impact.

Remote Telemetry Units Stem the Cost of Specialized Training and Keep You in the Loop

PLCs and PLRs often operate in proprietary protocols. However, many of them aren't compatible across platforms. They require special training to know and operate. RTUs from DPS come with their own easy to read graphical interface and most likely output in SNMP. They even report monitoring info from legacy or proprietary devices, so long as they output ASCII.

The NetGuardian series can also output plain-text alerts. They can report the status of controlled processes remotely, to technicians' e-mail, or cell phone. Your technicians don't have to be specially trained or waste man-hours sitting in a control booth. The NetGuardian 16 series RTUs even offer voice alerts right to your phone. If something were to go wrong with your process or other SCADA devices, you'd get a voice alert detailing the problem without having to wait for a call from a remote master. RTUs help you stay on top of your most important processes, so when something goes wrong, you can take action immediately.

RTUs are a cost-effective option in place of PLCs and PLRs providing a similar level of info and automation at remote sites. They are used for networking, communications, and transport processes.

Should You Choose an RTU or a PLC?

It doesn't matter if you decide to go with a PLC or an RTU, be positive that you know what you're purchasing and that the system covers all your needs. For this reason, always make sure to discuss your options with your potential vendor.

Don't compromise when it comes to your SCADA system. If you'd like to discuss more about RTUs and remote monitoring with me or with my team, we'd be glad to get in touch with you. Just contact us and we can get your perfect-fit solution started.

DNP3: Pros & Cons

Are you researching the best practices for remote monitoring at your sites? Or are you working toward migrating legacy gear? No matter what, if you're considering the purchase of DNP3 equipment, it's important to...

by Andrew Erickson on May 10, 2019

Read Full Article

RTUs vs PLCs: The Top Three RTU Problems You Need to Know About

If you want to start the process of implementing a remote monitoring or SCADA system in your network, then you're probably wondering if you should use an RTU or a PLC. You might be more inclined to choose an RTU if you...

by Andrew Erickson on April 26, 2019

Read Full Article

Get a Custom Application Diagram of Your Perfect-Fit Monitoring System

There is no other network on the planet that is exactly like yours. For that reason, you need to build a monitoring system that's the right fit for you.

"Buying more than you need" and "buying less than you need" are real risks. You also have to think about training, tech support, and upgrade availability.

Send me a quick online message about what you're trying to accomplish. I'll work with you to build a custom PDF application diagram that's a perfect fit for your network.

Make an Informed Decision

Your network isn't off-the-shelf.

Your monitoring system shouldn't be, either.

Customized monitoring application drawing

We'll walk you through this with a customized monitoring diagram.

Just tell us what you're trying to accomplish with remote monitoring.

Get a Custom Diagram