Understanding this layered model makes it easier to troubleshoot communication problems. When there is a problem, you can simply trace it down...
Now, we continue to examine the Simple Network Management Protocol (SNMP) focusing specifically on the layered communication model used to exchange information. Our last article focused on the structure of SNMP messages, however an SNMP message is not sent by itself. It is wrapped in the User Datagram Protocol (UDP), which in turn is wrapped in the Internet Protocol (IP). These are commonly referred to as layers and are based on a four-layer model developed by the Department of Defense (you may recall the DoD origins of the Internet).
SNMP resides in what is called the Application layer, UDP resides in the Transport layer and IP resides in the Internet layer (somewhat obvious). The fourth layer is the Network Interface layer where the assembled packet is actually interfaced to some kind of transport media (i.e., twisted pair copper, RG58 co-axial or fiber).
While this multi-layer model may seem a bit confusing, it effectively isolates the tasks of communication and ultimately assists in designing and implementing a network.
To illustrate the function of this layered model, let's look at a single SNMP GET request from the agent's perspective. The SNMP manager wants to know what the Agent's System Name is and prepares a GET message for the appropriate OID. It then passes the message to the UDP layer. The UDP layer adds a data block that identifies the manager port to which the response packet should be sent and the port on which it expects the SNMP agent to be listening for messages. The packet thus formed is then passed to the IP layer. Here a data block containing the IP and Media Access addresses of the manager and the agent is added before the entire assembled packet gets passed to the Network Interface layer. The Network Interface layer verifies media access and availability and places the packet on the media for transport.
After working its way across bridges and through routers (the modern equivalent of over the rivers and through the woods) based on the IP information, the packet finally arrives at the agent. Here it passes through the same four layers in exactly the opposite order as it did at the manager. First, it is pulled off the media by the Network Interface layer. After confirming that the packet is intact and valid, the Network Interface layer simply passes it to the IP layer. The IP layer verifies the Media Access and IP address and passes it on to the UDP layer where the target port is checked for connected applications. If an application is listening at the target port, the packet is passed to the Application layer. If the listening application is the SNMP agent, the GET request is processed as we have discussed in previous articles. The agent response then follows the identical path in reverse to reach the manager.
|An SNMP message passes through the protocol layers at both the manager and the agent. Each layer addresses a specific communication task.|
Understanding this layered model makes it easier to troubleshoot communication problems. When there is a problem, you can simply trace it down, out one end, into, and up the other. LAN/WAN link and activity status indicators provide some visibility to the Network Interface layer. ICMP echo requests and responses (Pings) provide some information regarding the proper functioning of the IP layer. SNMP processing indicators can be used to verify the passage of the packet through the UDP layer and the functioning of the Application layer. Each step can be verified independently until all steps are working correctly for end-to-end communication.
SNMP is a standard protocol that has wide acceptance in the industry and is flexible enough to describe almost anything. Because of these advantages, many network managers have come to believe that SNMP should be used for all network monitoring applications.
SNMP certainly has its place in an effective telecom network management solution, but this doesn't mean that any off-the-shelf SNMP manager can provide adequate visibility and control of your network.
The typical off-the-shelf SNMP manager is not designed for displaying and processing telemetry data for effective network monitoring, especially for the kind of real-world monitoring tasks network managers most need performed. These capabilities can be added to an SNMP manager, but it usually requires substantial custom software development.
Relying on off-the-shelf SNMP systems for mission-critical telemetry is a major mistake. If you're switching from traditional telemetry or integrating non-SNMP monitoring with an SNMP-based system, an off-the-shelf SNMP manager will not provide the detailed alarm data you expect. Before you commit to an SNMP monitoring solution, you need to make sure it supports essential network alarm monitoring functions.
There are seven common mistakes network managers typically make when integrating SNMP and non-SNMP monitoring. Your SNMP implementation will be successfully only if you can avoid them.
It is true that many, but not all, of these functions can be added to standard SNMP managers, but implementing network alarm monitoring in a basic SNMP manager usually involves a substantial amount of custom software module development. Even when pre-built software modules are available, they usually require custom tweaking to perform exactly as you want them to.
The need for extensive customization eliminates the advantage of using a simple open standard, and it is difficult to justify significant development costs after purchasing an already expensive SNMP manager. Why take the time, trouble, and expense to recreate capabilities that are already present in a high-quality, SNMP-capable network alarm management system?
Relying on an SNMP manager for critical network monitoring just doesn't take into account the tons of legacy and non-SNMP equipment that is functioning perfectly fine out in networks all over the world. The role of an SNMP manager is best used for inventorying network devices and drilling down into equipment details after your network monitoring system notifies you of a problem.
SNMP can be an effective tool, but it's only one item in your network alarm monitoring toolkit, and it can be used more effectively when it is part of a total network monitoring solution.
If you are looking to avoid these 7 mistakes, then the T/Mon network alarm monitoring system is for you. It is specifically designed to avoid them. Network managers who rely on T/Mon for their network alarm monitoring, notification, and control comment, "Looking at one map and knowing it represents every piece of equipment you're monitoring in the field… that's pretty good peace of mind."